I still recall being amazed reading and seeing it for the first time, and I have been eagerly awaiting to see what he been up to since starting Atomic Semi.
georgeburdell 19 hours ago [-]
I’m a semiconductor expert and without seeing the details, this seems like yet another smoke and mirrors wunderkind startup that will disperse once practical considerations are made. As far as I know, Mr. Zeloof has not made any fundamental advancements in any steps in manufacturing.
sq_ 1 days ago [-]
The article mentions, but doesn't explicitly state, that they're going to be using electron beam lithography. Makes sense for their low volume and/or prototype fab goal, but I'm curious how well that would work for prototyping to fab at high volume with the likes of TSMC or Intel.
I would assume that re-targeting a design to a different fab's process would change enough about it that you might as well just do verification in simulation rather than sidetrack through Fab2.
dinfinity 22 hours ago [-]
I think this might make a lot of sense in modern warfare scenarios: We're seeing in Ukraine that being able to produce weapons such as drones in very small production facilities using 3D printers and 'simple' technology makes it very hard for an adversary to shut down said production.
The more components can be produced in such a way, the better. Chips currently are quite an exception to that.
ipsum2 1 days ago [-]
I don't get it. How is Jim Keller running a brand new, hard tech startup while being CEO of Tenstorrent at the same time?
CoastalCoder 22 hours ago [-]
Chuck Norris will pass his torch to Jim Keller.
Jim won't have a say in the matter.
bhewes 1 days ago [-]
There are rumors Qualcomm is going to buy Tenstorrent.
So Elon Musk can be the CEO of multiple companies but Jim Keller can't be CEO of two quickly growing startups?
inigyou 11 hours ago [-]
Elon is a notoriously bad CEO at all of those companies.
rowanG077 10 hours ago [-]
Just by success numbers he can't be terrible. Most of his companies are doing pretty well for themselves.
inigyou 10 hours ago [-]
By only one metric really, which is market capitalisation. SpaceX, which is famously shielded from Elon by the next level of managers, also produces a useful and profitable product.
tangenter 22 hours ago [-]
I thought Elon runs off of Special
K and hardcore Mephisto drops?
jtullos 19 hours ago [-]
Applied for a job, but their recruiter was trash. Still, hope it works out for the company.
ripe 22 hours ago [-]
I would've liked to read more about what they're doing, but their website fab2.com is unhelpful. Very little info, presented in pointless swirling animations that hijack your scroll action.
Animats 15 hours ago [-]
Yes, the web site is all effects, no content. It's like an old Flash site.
E-beam machines work fine for prototyping. People have been doing that since the 1970s. But they're slow. It's a prototyping technology. The sort of thing that "3D print everything" people like. E-beam machines with many beams have been mentioned, but never seemed to be worth it.
There are companies which offer E-beam IC fab as a service. Some cater to DoD and the intelligence community.[2] (That's for when you really can't trust your supply chain and want your own ICs fabbed.) Others are more commercial, but are in China.[3]
They claim to be building all the machines needed for a fab. But they don't have a list, or pictures. There's a used market in that gear, and no reason to build it all yourself.
It's not a fundamentally bad idea, but the hype is strong here.
One of the most interesting technologies that is not about LLMs/AIs.
1 days ago [-]
eikenberry 1 days ago [-]
Is this an ASML competitor?
rasz 10 hours ago [-]
This is "we fit on small FPGA but dont want to ship cheap commodity off the shelf hardware for some bizarre reason while cant even afford structured ASIC (you only pay for metal layer masks)" competitor maybe.
Unless they offer some amazing analog capabilities.
re-thc 1 days ago [-]
No, quoting the article:
> only really suits prototyping and low-volume runs rather than high-volume production at commercial foundries
fernie 1 days ago [-]
Aww, I really wanted a cottage industry of chip manufacturing
wyre 22 hours ago [-]
I'm sorry but isn't cottage industry synonymous with small-scale manufacturing? It seems like fab2 is the definition of cottage industry chip manugacturing.
RetroTechie 20 hours ago [-]
> I'm sorry but isn't cottage industry synonymous with small-scale manufacturing?
Wouldn't many 1000s of mini-fabs make for a significant combined manufacturing capacity?
wyre 19 hours ago [-]
Thats what a cottage industry is? A lot of small producers making up a larger industry.
syntaxing 22 hours ago [-]
This is a great idea and hope it works out, especially on shoring chips back here in the states. That being said, their website is absolutely atrocious. One of the very few sites I got motion sickness from scrolling.
It even manages to lag on my one year old flagship phone! Impressive! :)
TacticalCoder 20 hours ago [-]
> ... chip architect Jim Keller and DIY fabrication pioneer Sam Zeloof, has rebranded as Fab2 and moved its operations to Texas
> Fab2 now operates three sites: a 120,000 square foot facility in Austin serves as the new headquarters for research and production, a 30,000 square foot site in Lockhart houses the "fab fab" itself, and the original 25,000 square foot "garage fab" remains in San Francisco.
> Fab2 said it shifted its hiring focus to Texas after four years in California
Is California not what it used to be for startups? (I'm not saying Texas doesn't have an history of tech startups: it had the likes of Texas Instruments and many others in the early days)
How could would ut be that your company or university or even at home has its own chip machine. Design your 5b transistor chip and bake and process it the same day. Doable I would say.
vatsachak 1 days ago [-]
Great! Hopefully we can get 10 year behind technology from small fabs. There's so much you can do with a laptop from 2016
adrian_b 17 hours ago [-]
No, you misunderstood.
A small fab that uses electron-beam lithography can do everything that TSMC can do, and in a much simpler way.
Its problems are not technical, but economical.
The costs of producing chips are much lower than for TSMC, but the production rate is also orders of magnitude lower.
So they can be used only to produce prototypes or devices for niche applications, where the small quantities needed would never allow them to be produced at a big fab.
On the other hand, if such small fabs could be themselves mass produced, so that their cost could become low enough, then using a great number of such small fabs could satisfy the requirements in semiconductor devices and ICs of most not too big countries, and this style of production would be greatly preferable to what exists today as the end point of a long chain of acquisitions and mergers, that has resulted in a handful of SOTA manufacturers in the entire world.
Ideally, there would still exist big fabless IC design companies, like Intel, AMD or NVIDIA, but they would design for a standardized CMOS fabrication process, not for a proprietary process with secret design rules, like those of TSMC.
Then such designs would be licensed for production in distributed small fabs. Only such a system would remove the dependence of the entire world on a quasi-monopolistic system of production, where the destruction of a single fab could cripple most of the world.
pulse7 1 days ago [-]
With electron-beam lithography you can build transistors with gate lengths down to 1 to 3 nanometers.
adrian_b 17 hours ago [-]
Using electron-beam lithography, you can define features of that size on a silicon wafer.
Silicon transistors with such gate lengths would not work, because the too short gate could not close the conduction channel (the minimum gate length with silicon is likely to be greater than 10 nm, even with gate-around transistors).
The masks used for deep UV lithography or for any other kind of high-resolution lithography are also made with electron-beam lithography.
Therefore it is obvious that anything that you can do in a form of lithography that uses masks you can do with electron-beam lithography.
Using directly electron-beam lithography skips the production of masks and their use.
This is a huge cost reduction in the cost of processing a single wafer (which may have hundreds or thousands of chips). However the processing throughput is orders of magnitude lower than when using masks. For very high-volume production, the costs of the masks and of the deep UV lithography are divided over millions or billions of chips, so they are reduced to a reasonable fraction of the cost, which is compensated by the high productivity.
phonon 24 hours ago [-]
Global Foundries has lots of fabs with 10 year old+ processes....
https://en.wikipedia.org/wiki/Sam_Zeloof
I still recall being amazed reading and seeing it for the first time, and I have been eagerly awaiting to see what he been up to since starting Atomic Semi.
I would assume that re-targeting a design to a different fab's process would change enough about it that you might as well just do verification in simulation rather than sidetrack through Fab2.
The more components can be produced in such a way, the better. Chips currently are quite an exception to that.
Jim won't have a say in the matter.
E-beam machines work fine for prototyping. People have been doing that since the 1970s. But they're slow. It's a prototyping technology. The sort of thing that "3D print everything" people like. E-beam machines with many beams have been mentioned, but never seemed to be worth it.
There are companies which offer E-beam IC fab as a service. Some cater to DoD and the intelligence community.[2] (That's for when you really can't trust your supply chain and want your own ICs fabbed.) Others are more commercial, but are in China.[3]
They claim to be building all the machines needed for a fab. But they don't have a list, or pictures. There's a used market in that gear, and no reason to build it all yourself.
It's not a fundamentally bad idea, but the hype is strong here.
[1] https://www.machinio.com/semiconductors
[2] https://www.hrl.com/laboratories/mtl
[3] https://en.omedasemi.com/electron_beam_lithography.html
Unless they offer some amazing analog capabilities.
> only really suits prototyping and low-volume runs rather than high-volume production at commercial foundries
Wouldn't many 1000s of mini-fabs make for a significant combined manufacturing capacity?
[1] https://fab2.com/
> Fab2 now operates three sites: a 120,000 square foot facility in Austin serves as the new headquarters for research and production, a 30,000 square foot site in Lockhart houses the "fab fab" itself, and the original 25,000 square foot "garage fab" remains in San Francisco.
> Fab2 said it shifted its hiring focus to Texas after four years in California
Is California not what it used to be for startups? (I'm not saying Texas doesn't have an history of tech startups: it had the likes of Texas Instruments and many others in the early days)
A small fab that uses electron-beam lithography can do everything that TSMC can do, and in a much simpler way.
Its problems are not technical, but economical.
The costs of producing chips are much lower than for TSMC, but the production rate is also orders of magnitude lower.
So they can be used only to produce prototypes or devices for niche applications, where the small quantities needed would never allow them to be produced at a big fab.
On the other hand, if such small fabs could be themselves mass produced, so that their cost could become low enough, then using a great number of such small fabs could satisfy the requirements in semiconductor devices and ICs of most not too big countries, and this style of production would be greatly preferable to what exists today as the end point of a long chain of acquisitions and mergers, that has resulted in a handful of SOTA manufacturers in the entire world.
Ideally, there would still exist big fabless IC design companies, like Intel, AMD or NVIDIA, but they would design for a standardized CMOS fabrication process, not for a proprietary process with secret design rules, like those of TSMC.
Then such designs would be licensed for production in distributed small fabs. Only such a system would remove the dependence of the entire world on a quasi-monopolistic system of production, where the destruction of a single fab could cripple most of the world.
Silicon transistors with such gate lengths would not work, because the too short gate could not close the conduction channel (the minimum gate length with silicon is likely to be greater than 10 nm, even with gate-around transistors).
The masks used for deep UV lithography or for any other kind of high-resolution lithography are also made with electron-beam lithography.
Therefore it is obvious that anything that you can do in a form of lithography that uses masks you can do with electron-beam lithography.
Using directly electron-beam lithography skips the production of masks and their use.
This is a huge cost reduction in the cost of processing a single wafer (which may have hundreds or thousands of chips). However the processing throughput is orders of magnitude lower than when using masks. For very high-volume production, the costs of the masks and of the deep UV lithography are divided over millions or billions of chips, so they are reduced to a reasonable fraction of the cost, which is compensated by the high productivity.